| TOPIC | POSTED BY | REPLIES | LAST POST |
|---|---|---|---|
| 1by4rs | Guest User | 2 | 8/29/13 8:57 PM |
| Underlayment | Neal Young | 5 | 8/29/13 11:30 AM |
| Metal Roof over strapping? | Guest User | 3 | 8/23/13 9:22 AM |
| Re-Roofing an old barn - Shingles to Steel | Guest User | 3 | 8/21/13 11:27 AM |
| CUT EDGES | JOE NATALI | 3 | 8/21/13 11:26 AM |
| Skylites on a low pitch roof | Marc Bergman | 2 | 8/19/13 9:28 AM |
| insulation under metal roof | Raymond Abel | 3 | 8/16/13 8:16 PM |
| underlay and decking required? | Edward Ake | 3 | 8/13/13 8:14 AM |
| shake roof | Guest User | 2 | 8/10/13 10:17 AM |
| Installation over structural metal deck | Jim Fillerup | 2 | 8/2/13 10:34 AM |
| House wrap prior to installation? | Guest User | 3 | 8/2/13 6:20 AM |
| underlayment? | Guest User | 5 | 8/2/13 6:18 AM |
| Sealing ends of gable trim | Guest User | 5 | 7/31/13 5:11 PM |
| Miter Cuts | Guest User | 2 | 7/30/13 8:50 AM |
| Roof vent | john J | 13 | 7/26/13 10:26 PM |
| underlayment | John Scott | 8 | 7/24/13 11:32 AM |
| installation | perry hudson | 3 | 7/21/13 9:19 AM |
| Ridge vents | Billy Watson | 4 | 7/14/13 9:52 PM |
| Which way is right? | Jerry Brandt | 7 | 7/10/13 5:25 PM |
| Screw sources, types, performance, recomendations | Jim Gerken | 2 | 7/8/13 10:23 AM |
- Previous
- 1 -20
- 21 -40
- 41 -60
- 61 -80
- 81 -100
- 101 -120
- 121 -140
- 141 -160
- 161 -180
- 181 -200
- 201 -220
- 221 -240
- 241 -260
- 261 -280
- 281 -300
- 301 -320
- 321 -340
- 341 -360
- 361 -380
- 381 -400
- 401 -420
- 421 -440
- 441 -460
- 461 -480
- 481 -500
- 501 -520
- 521 -540
- 541 -560
- 561 -580
- 581 -600
- 601 -620
- 621 -640
- 641 -660
- 661 -680
- 681 -700
- 701 -720
- 721 -740
- 741 -760
- 761 -780
- 781 -800
- 801 -820
- 821 -837
- Next
No advice or information obtained through the forum or this website shall create any warranty by MRA or its contributors whatsoever and all warranties are disclaimed. MRA and its contributors disclaim any liability of any kind arising out of or relating to use of the answers or information provided hereunder, and by using the forum, you agree to waive any claims against MRA and its contributors and hold them harmless from any liability or damages of any kind arising out of or relating to the forum. For a detailed description of the terms and conditions of use of the Forum and this website, including a more detailed description of disclaimers of warranties and limitations of liability, please see the Terms and Conditions section of this website. MRA does not endorse or recommend any commercial products, processes, or services. The views and opinions of contributors to this Forum do not necessarily state or reflect those of MRA or its members, and they may not be used for advertising or product endorsement purposes.