| TOPIC | POSTED BY | REPLIES | LAST POST |
|---|---|---|---|
| Roofing on new home | Jennifer T | 2 | 8/5/16 2:17 PM |
| Metal Ridge Vent | Teriann Shrum | 17 | 7/23/16 8:10 PM |
| heat reflective decking or just slats | David Vaculin | 4 | 7/22/16 9:50 PM |
| Fastener location | Guest User | 2 | 7/21/16 6:39 AM |
| recommended fasteners | steve BRENNER | 2 | 7/18/16 11:28 PM |
| Best seam for 2:12 roof | Derrick Gardiner | 7 | 7/13/16 4:59 PM |
| 12x24 run-in shed | Robin Talsma | 14 | 7/6/16 6:52 AM |
| Installation of metal roof to 7/16" OSB | David Chambers | 2 | 7/4/16 3:23 PM |
| Commercial panel identification and installation | Guest User | 2 | 6/18/16 5:34 AM |
| Metal on torch down | Dont WantTo | 7 | 6/17/16 1:11 PM |
| Metal to shingle | Walter Butler | 2 | 6/9/16 8:28 PM |
| New low slope metal roof that interfaces with higher slope existing shingled roof | Randall Moore | 3 | 6/8/16 10:08 PM |
| Proper Installation Over Shingles- Metal Roof Noobie | Jarret Blair | 12 | 6/8/16 7:51 PM |
| I need new metal roof advide | Guest User | 2 | 6/7/16 5:22 AM |
| Installation | Guest User | 2 | 5/31/16 11:40 AM |
| Flashing for top edge of shed roof? | Colleen Thompson | 2 | 5/27/16 6:28 PM |
| Eave / Gutter flashing | Mike Tatarnikov | 6 | 5/22/16 10:54 AM |
| Cutting metal roofing | Guest User | 2 | 5/19/16 8:57 PM |
| min. pitch | michael koch | 2 | 5/18/16 10:07 AM |
| Slats or no slats | Mike Hozjan | 5 | 5/16/16 8:57 AM |
- Previous
- 1 -20
- 21 -40
- 41 -60
- 61 -80
- 81 -100
- 101 -120
- 121 -140
- 141 -160
- 161 -180
- 181 -200
- 201 -220
- 221 -240
- 241 -260
- 261 -280
- 281 -300
- 301 -320
- 321 -340
- 341 -360
- 361 -380
- 381 -400
- 401 -420
- 421 -440
- 441 -460
- 461 -480
- 481 -500
- 501 -520
- 521 -540
- 541 -560
- 561 -580
- 581 -600
- 601 -620
- 621 -640
- 641 -660
- 661 -680
- 681 -700
- 701 -720
- Next
No advice or information obtained through the forum or this website shall create any warranty by MRA or its contributors whatsoever and all warranties are disclaimed. MRA and its contributors disclaim any liability of any kind arising out of or relating to use of the answers or information provided hereunder, and by using the forum, you agree to waive any claims against MRA and its contributors and hold them harmless from any liability or damages of any kind arising out of or relating to the forum. For a detailed description of the terms and conditions of use of the Forum and this website, including a more detailed description of disclaimers of warranties and limitations of liability, please see the Terms and Conditions section of this website. MRA does not endorse or recommend any commercial products, processes, or services. The views and opinions of contributors to this Forum do not necessarily state or reflect those of MRA or its members, and they may not be used for advertising or product endorsement purposes.